問題1
Hotspot Question
A static map to the S-AMER location is required.
Which command should be used to create this map?
Hotspot Question
A static map to the S-AMER location is required.
Which command should be used to create this map?
正確答案: D
說明：（僅 NewDumps 成員可見）
問題2
While troubleshooting the failure of an OSPFv3 Ethernet connection between router R1 and R2, you determine that the hello timer are mismatched and that R2 is configured with default settings, which command do you enter on R1 to correct the problem?
While troubleshooting the failure of an OSPFv3 Ethernet connection between router R1 and R2, you determine that the hello timer are mismatched and that R2 is configured with default settings, which command do you enter on R1 to correct the problem?
正確答案: D
說明：（僅 NewDumps 成員可見）
問題3
Which two outcomes are effects of configuring the snmp-server host 10.1.1.1 traps version 3 auth md5 cisco command on router R1? (Choose two.)
Which two outcomes are effects of configuring the snmp-server host 10.1.1.1 traps version 3 auth md5 cisco command on router R1? (Choose two.)
正確答案: D,E
問題4
After you configure a GRE tunnel between two networks, the tunnel comes up normally, but workstations on each side of the tunnel cannot communicate.
Which reason for the problem is most likely true?
After you configure a GRE tunnel between two networks, the tunnel comes up normally, but workstations on each side of the tunnel cannot communicate.
Which reason for the problem is most likely true?
正確答案: D
問題5
What is the default encapsulation type for Cisco WAN serial interfaces?
What is the default encapsulation type for Cisco WAN serial interfaces?
正確答案: C
問題6
A router has learned three possible routes that could be used to reach a destination network One route is from EIGRP and has a composite metric of 07104371. Another route is from OSPF with a metric of 782 The last is from RIPv2 and has a metric of 4 Which route or routes will the router install in the routing table?
A router has learned three possible routes that could be used to reach a destination network One route is from EIGRP and has a composite metric of 07104371. Another route is from OSPF with a metric of 782 The last is from RIPv2 and has a metric of 4 Which route or routes will the router install in the routing table?
正確答案: C
問題7
Which six-byte field in a basic ethernet frame must be an individual address ?
Which six-byte field in a basic ethernet frame must be an individual address ?
正確答案: A
問題8
Which two factors can affect the price of leased point-to-point WAN links? (Choose two.)
Which two factors can affect the price of leased point-to-point WAN links? (Choose two.)
正確答案: A,C
問題9
Drag and Drop Question
Drag and drop the BGP peering states from the left onto the correct statements on the right.
Drag and Drop Question
Drag and drop the BGP peering states from the left onto the correct statements on the right.
正確答案:
問題10
What is true about Ethernet? (Choose Two.)
What is true about Ethernet? (Choose Two.)
正確答案: C,E
問題11
You work as a network engineer for SASCOM Network Ltd company. On router HQ, a provider link has been enabled and you must configure an IPv6 default route on HQ and make sure that this route is advertised in IPv6 OSPF process. Also, you must troubleshoot another issue. The router HQ is not forming an IPv6 OSPF neighbor relationship with router BR.
Topology Details
Two routers HQ and BR are connected via serial links.
Router HQ has interface Ethernet0/1 connected to the provider cloud and interface Ethernet 0/0 connected to RA1 Router BR has interface Ethernet 0/0 connected to another router RA2.
IPv6 Routing Details
Ail routers are running IPv6 OSPF routing with process ID number 100 Refer to the topology diagram for information about the OSPF areas The Loopback 0 IPv4 address is the OSPF router ID on each router Configuration requirements
- Configure IPv6 default route on router HQ with default gateway as
2001:DB8:B:B1B2::1.
- Verify by pinging provider test IPv6 address 2001 :DB8:0:1111:1 after configuring default route on HQ.
- Make sure that the default route is advertised in IPv6 OSPF on router HQ This default route should be advertised only when HQ has a default route in its routing table.
- Router HQ is not forming IPv6 OSPF neighbor with BR. You must
troubleshoot and resolve this issue
Special Note: To gain the maximum number of points, you must complete the necessary configurations and fix IPv6 OSPF neighbor issue with router BR IPv6 OSPFv3 must be configured without using address families. Do not change the IPv6 OSPF process ID.
You work as a network engineer for SASCOM Network Ltd company. On router HQ, a provider link has been enabled and you must configure an IPv6 default route on HQ and make sure that this route is advertised in IPv6 OSPF process. Also, you must troubleshoot another issue. The router HQ is not forming an IPv6 OSPF neighbor relationship with router BR.
Topology Details
Two routers HQ and BR are connected via serial links.
Router HQ has interface Ethernet0/1 connected to the provider cloud and interface Ethernet 0/0 connected to RA1 Router BR has interface Ethernet 0/0 connected to another router RA2.
IPv6 Routing Details
Ail routers are running IPv6 OSPF routing with process ID number 100 Refer to the topology diagram for information about the OSPF areas The Loopback 0 IPv4 address is the OSPF router ID on each router Configuration requirements
- Configure IPv6 default route on router HQ with default gateway as
2001:DB8:B:B1B2::1.
- Verify by pinging provider test IPv6 address 2001 :DB8:0:1111:1 after configuring default route on HQ.
- Make sure that the default route is advertised in IPv6 OSPF on router HQ This default route should be advertised only when HQ has a default route in its routing table.
- Router HQ is not forming IPv6 OSPF neighbor with BR. You must
troubleshoot and resolve this issue
Special Note: To gain the maximum number of points, you must complete the necessary configurations and fix IPv6 OSPF neighbor issue with router BR IPv6 OSPFv3 must be configured without using address families. Do not change the IPv6 OSPF process ID.
正確答案:
1. Configure default route on router HQ:
ipv6 unicast-routing ipv6 route ::/0 2001:DB8:B:B1B2::1
2. Advertise this route under ospfv3
Ipv6 router ospf 100
Default-information originate
3. Fix adjacency problem if a area mismatches
We need to enter in s1/0
Ipv6 ospf 100 area 0
ipv6 unicast-routing ipv6 route ::/0 2001:DB8:B:B1B2::1
2. Advertise this route under ospfv3
Ipv6 router ospf 100
Default-information originate
3. Fix adjacency problem if a area mismatches
We need to enter in s1/0
Ipv6 ospf 100 area 0
問題12
A security administrator wants to profile endpoints and gain visibility into attempted authentications. Which 802.1x mode allows these actions?
A security administrator wants to profile endpoints and gain visibility into attempted authentications. Which 802.1x mode allows these actions?
正確答案: B
問題13
Which two numbers are valid extended VLAN numbers? (Choose two)
Which two numbers are valid extended VLAN numbers? (Choose two)
正確答案: A,E
問題14
Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the reasons that interface FastEthernet 0/10 is not the root port for VLAN 2?
Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the reasons that interface FastEthernet 0/10 is not the root port for VLAN 2?
正確答案: D
說明：（僅 NewDumps 成員可見）
問題15
Drag and Drop Question
Drag and drop the SDN components from the left onto the correct API types on the right.
Drag and Drop Question
Drag and drop the SDN components from the left onto the correct API types on the right.
正確答案:
