問題1
A branch device is powered on with factory-default staging configuration. The device establishes an IKE session to the staging server and receives an IP address, but it does not proceed to establish an IKE session with the Versa Controller. Which staging phase is failing?
A branch device is powered on with factory-default staging configuration. The device establishes an IKE session to the staging server and receives an IP address, but it does not proceed to establish an IKE session with the Versa Controller. Which staging phase is failing?
正確答案: C
說明：（僅 NewDumps 成員可見）
問題2
During branch onboarding, you need to verify whether the Controller has sent branch-connect and branch- disconnect notifications to Versa Director. Which CLI command should be used?
During branch onboarding, you need to verify whether the Controller has sent branch-connect and branch- disconnect notifications to Versa Director. Which CLI command should be used?
正確答案: C
說明：（僅 NewDumps 成員可見）
問題3
Examine the exhibit below.
As an administrator of a Versa Secure SD-WAN deployment, you are asked to find the current bandwidth of each WAN circuit used for SD-WAN connectivity in a branch, but Versa Director is not displaying any information for the WAN circuits. In this scenario, what should be done to get the graph populated for all WAN circuits?
Examine the exhibit below.
As an administrator of a Versa Secure SD-WAN deployment, you are asked to find the current bandwidth of each WAN circuit used for SD-WAN connectivity in a branch, but Versa Director is not displaying any information for the WAN circuits. In this scenario, what should be done to get the graph populated for all WAN circuits?
正確答案: C
說明：（僅 NewDumps 成員可見）
問題4
A tenant uses CGNAT for internet breakout. You want to verify whether CGNAT rules, pools, static NAT entries, subscribers, and endpoint-independent mapping entries are programmed in the vsmd daemon for a tenant. Which command should you use after connecting to vsmd?
A tenant uses CGNAT for internet breakout. You want to verify whether CGNAT rules, pools, static NAT entries, subscribers, and endpoint-independent mapping entries are programmed in the vsmd daemon for a tenant. Which command should you use after connecting to vsmd?
正確答案: D
說明：（僅 NewDumps 成員可見）
問題5
Examine the exhibit below.
You are configuring an IPsec tunnel towards a non-SD-WAN site over the INETTransport-VR. The site IP address is 10.1.1.1. This tunnel is for traffic between the 192.168.100.0/24 and the 192.168.200.0/24 LAN networks. The tunnel does not establish.
Referring to the exhibit, which statement is correct?
Examine the exhibit below.
You are configuring an IPsec tunnel towards a non-SD-WAN site over the INETTransport-VR. The site IP address is 10.1.1.1. This tunnel is for traffic between the 192.168.100.0/24 and the 192.168.200.0/24 LAN networks. The tunnel does not establish.
Referring to the exhibit, which statement is correct?
正確答案: B
說明：（僅 NewDumps 成員可見）
問題6
Examine the exhibit below.
Spoke1 and Spoke2 are part of Spoke-to-Hub-Only spoke group, the hub is advertising a default route to both the spokes.
Referring to the exhibit, which statement is true?
Examine the exhibit below.
Spoke1 and Spoke2 are part of Spoke-to-Hub-Only spoke group, the hub is advertising a default route to both the spokes.
Referring to the exhibit, which statement is true?
正確答案: A
說明：（僅 NewDumps 成員可見）
問題7
Examine the exhibit below.
According to the CGNAT pool configuration shown in the exhibit, which two statements are true? (Choose two.)
Examine the exhibit below.
According to the CGNAT pool configuration shown in the exhibit, which two statements are true? (Choose two.)
正確答案: B,C
說明：（僅 NewDumps 成員可見）